RCA Soundbar Remote Control Codes | Updated 2023

RCA Soundbar Remote Control Codes

Greetings, dear readers! We are delighted to have you here as we dive into the world of RCA Soundbar remote control codes. If you own an RCA Soundbar and wish to enhance your entertainment setup with the convenience of a universal remote, you’ve come to the right place. In this blog, we have compiled a comprehensive list of remote control codes that will allow you to effortlessly synchronize your RCA Soundbar with various universal remotes, TV remotes, cable remotes, or SAT remotes.

With the correct programming instructions and remote codes at your fingertips, you can take full control of your sound bar from the comfort of your favourite spot. And fear not, if you encounter any hiccups along the way, we’ve got your back! Let’s embark on this journey together to unlock the full potential of your RCA Soundbar with the power of universal remote control.

RCA Soundbar 5 Digit Remote Control Codes
Most likely to work:

  • 20060
  • 31254
  • 30531

RCA Soundbar Universal Remote 5 Digit Codes

2106033969
3036031390
3145921014
3082331511
2004220035
3204133295
3309130531
3102333297
3139021035
3242631963
3160920807
3336331023
2014932655

Your Soundbar will be set up with your preferred universal remote control if any of those codes don’t work, therefore try another one and repeat this process with more codes from the list.

RCA Soundbar Universal Remote Without Codes

All universal remote control codes are scanned in the remote during the auto-search procedure. To program the control, it scans one code at a time to determine the correct remote code that works with your remote. Follow the instructions below:

  • Turn on the smart device you want to use the universal remote to control, such as the TV.
  • To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for three seconds. The device is prepared to program, according to the LED light.
  • Use the remote to select the “CH+” and “CH-” switches. On/off indications are displayed on the remote. Press the “up” or “down” key until the device turns off.
  • Click the “power” key to confirm the code. It should start up. If it does, try a different channel to make sure the remote is programmed correctly.

To store the code, press the “device” button now. The device’s LED will flash twice to verify the code that was held.

Read Also: program cablevision remote optimum remote programming guide

RCA Soundbar Universal Remote With Manual Method

The universal remote may be readily programmed using the keycode, which also serves to identify the make and model of your equipment.

  • You must “Turn The Device On” first.
  • Press the “TV” button on your “RCA Soundbar universal remote”
  • As soon as the universal remote displays the “Light Flash” (a sign that it is in “Learning mode”), push and hold the “Setup button” for a few seconds.
  • Finally, enter the “Keycode” that you have obtained from the Instructions Booklet for programming.
  • Simply “point your remote at the TV” after completing this step, and then “Press and Hold The Power” button.
  • When the screen dims, you can let go of the “Power Button”

That’s it; the universal remote will now make your TV function perfectly. That’s all there is to it; your TV should now work perfectly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

You can set your universal remote to search mode and look for the right key code if you are unable to find it at that time. The remote control is forced into search mode by a code in the instructions.

  • “Turn The Device On” first.
  • Hold down the “Setup” button for a moment.
  • Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case your TV, “Turns Off.”

Finding your key code may take a little more time using the above method, but it is very important. Once you’ve followed the steps above, your remote control should function.

Troubleshooting Tips

Troubleshooting Tips for RCA Soundbar Remote Control Issues:

  1. Check Batteries: Ensure the remote’s batteries are fresh and properly inserted. Weak batteries can lead to unresponsiveness.
  2. Line of Sight: Make sure there are no obstructions between the remote and the soundbar’s sensor. Clear any obstacles for better signal transmission.
  3. Verify Remote Codes: Double-check that you’ve entered the correct remote code for your RCA Soundbar. Refer to the manual or RCA’s website for accurate codes.
  4. Try Auto-Programming: If available, use the remote’s auto-programming feature to search for the correct code automatically.
  5. Reset the Remote: Consider resetting your universal remote to its default settings. Follow the manual’s instructions to perform the reset.
  6. Ensure Compatibility: Confirm that your remote is compatible with RCA Soundbars. Some universal remotes may not support all models.
  7. Update Firmware: Check for any firmware updates for your universal remote. Upgrades may improve compatibility and performance.
  8. Test with Other Devices: Try using the remote with other devices to ensure it’s functioning correctly. This helps isolate the issue.
  9. Factory Reset Soundbar: If the soundbar is unresponsive, perform a factory reset as per the user manual’s guidelines.
  10. Contact Support: If all else fails, contact RCA or the remote manufacturer’s customer support for further assistance in resolving the issue.

FAQs

My universal remote isn’t responding to the soundbar. What should I do?

First, check if the remote has fresh batteries and a clear line of sight to the soundbar’s sensor. Re-enter the correct remote code, and try auto-programming if available.

Are there any firmware updates for my universal remote?

Check the manufacturer’s website for firmware updates, as they may enhance compatibility and resolve issues with your RCA Soundbar.

Leave a Comment