Sharp DVD Universal Remote Codes

Hello! How are you doing? Do you have a Sharp DVD Player? Would you like to use your selected Sharp DVD player remote control to operate it? So here we are to help you! We offer a variety of programming methods as well as universal remote control codes. You just need to enter the codes in accordance with the ways listed below because they are universal remote control compatible. Hence, just use the 4 and 5-digit numbers that we mentioned.

Sharp DVD Universal Remote Codes

We have the necessary codes if you have a Sharp DVD player and want to use a universal remote control to control it. If you have the right programming manual and the right remote codes for the DVD player, you can use any universal remote to control a Sharp DVD player.

Sharp DVD Universal Remote Codes For One For All



  • 2082

Sharp DVD Universal Remote 4 Digit Codes

  • 0695
  • 0630
  • 0752
  • 2170
  • 2174
  • 2227
  • 2044
  • 2082
  • 2086

Sharp DVD Universal Remote 5 Digit Codes

  • 20630
  • 21419
  • 22250
  • 22561
  • 20675
  • 20752
  • 21256

In the auto search method all universal remote control codes are scanned in the remote  To programme the control, it scans one code at a time to find the right remote code that works with your remote. Read the instructions below:

  • Turn on the smart device you want to use the universal remote to control, such as the TV.
  • To “turn on” a device, press and hold the TV, DVD, CBL, and OK/SEL buttons for 3 seconds. The device is ready to programme, according to the LED light.
  • Use the remote to choose the “CH+” and “CH-“ switches. 
  • On/off signals are displayed on the remote. Continuously press the “up” or “down” key until the device turns off.
  • Click the “power” key to confirm the code. It should start up. If it does, check a different channel to make sure the remote is programmed properly.
  • To save the code, press the “device” button now. The device’s LED will flash twice to verify the code that was saved.

How to Program Sharp DVD Universal Remote With Manual Method

We can quickly programme a universal remote control using the keycode, and the keycode also informs us what brand and type of equipment you have.

  • You must first “Turn The Device On.”
  • On your “Sharp DVD universal remote,” choose “TV.”
  • In order to set the universal remote in “learning mode,” press and hold the “Setup button” until it flashes a light.
  • At last, key in the “Keycode” you collected from the programming manual (Instructions Booklet)
  • Just “point your remote at the TV” after completing this procedure, and then “Press and Hold The Power” button.
  • When the screen switches off, you can release the “Power Button.”
  • That’s all there is to it; your TV should now operate perfectly with the universal remote control. If not, try repeating the process with a new code from the same section of the reference table.

Your universal remote can be programmed to search mode to find the right key code if you are unable to find it at that time. The remote control is forced into search mode by a code in the instructions.

  • First, “Turn The device On”
  • Press and hold the “Setup” button .
  • Enter the “9-9-1” (three-digit) code after which you must continue to hold down the “Power Button” on the remote control while pressing the Channel up button until the device, in this case your TV, “Turns Off.”
  • Finding your key code may require some extra effort using the above method, but it is very important.
  • Your remote should function properly for all in the functions once you have completed the above procedure.


To ensure that all the codes on this page are relevant with your device, we often update this website. If you can’t seem to find the correct code, don’t hesitate to drop us a note and we’ll do our best to help. Your opinions and recommendations concerning this subject and how we might enhance the website are appreciated.


How do I connect my universal remote?

Power on the TV or other device you’d like to connect to.
Insert batteries into your remote and point at the device.
Press and release the correct device button on your remote for the device you’re connecting. …
Now press the power button and the device button simultaneously.

What is a DVD digital code?

A digital code is a code that is packaged with a physical product, such as a DVD or Blu-ray, that is suitable for Movies Anywhere. Digital movie coupons may be redeemed in Movies Anywhere to obtain a digital copy of the film, which will be added to your library.

Leave a Comment